Part Details for MB8S by Yangzhou Yangjie Electronics Co Ltd
Results Overview of MB8S by Yangzhou Yangjie Electronics Co Ltd
- Distributor Offerings: (1 listing)
- Number of FFF Equivalents: (1 replacement)
- CAD Models: (Request Part)
- Number of Functional Equivalents: (9 options)
- Part Data Attributes: (Available)
- Reference Designs: (Not Available)
Tip: Data for a part may vary between manufacturers. You can filter for manufacturers on the top of the page next to the part image and part number.
MB8S Information
MB8S by Yangzhou Yangjie Electronics Co Ltd is a Bridge Rectifier Diode.
Bridge Rectifier Diodes are under the broader part category of Diodes.
A diode is a electrical part that can control the direction in which the current flows in a device. Consider factors like voltage drop, current capacity, reverse voltage, and operating frequency when selecting a diode. Read more about Diodes on our Diodes part category page.
Price & Stock for MB8S
| Part # | Distributor | Description | Stock | Price | Buy | |
|---|---|---|---|---|---|---|
|
DISTI #
MB8S-YAN
|
TME | Bridge rectifier: single-phase, 800V, If: 0.8A, Ifsm: 30A, MBS, SMT Min Qty: 5 | 550 |
|
$0.0489 / $0.2010 | Buy Now |
Part Details for MB8S
MB8S CAD Models
MB8S Part Data Attributes
|
|
MB8S
Yangzhou Yangjie Electronics Co Ltd
Buy Now
Datasheet
|
Compare Parts:
MB8S
Yangzhou Yangjie Electronics Co Ltd
Bridge Rectifier Diode, 0.8A, 800V V(RRM),
Select a part to compare: |
| Rohs Code | Yes | |
| Part Life Cycle Code | Active | |
| Ihs Manufacturer | YANGZHOU YANGJIE ELECTRONICS CO LTD | |
| Reach Compliance Code | compliant | |
| ECCN Code | EAR99 | |
| Configuration | BRIDGE, 4 ELEMENTS | |
| Diode Element Material | SILICON | |
| Diode Type | BRIDGE RECTIFIER DIODE | |
| Forward Voltage-Max (VF) | 1 V | |
| Non-rep Pk Forward Current-Max | 30 A | |
| Number of Elements | 4 | |
| Number of Phases | 1 | |
| Operating Temperature-Max | 150 °C | |
| Output Current-Max | 0.5 A | |
| Rep Pk Reverse Voltage-Max | 800 V | |
| Surface Mount | YES |
Alternate Parts for MB8S
This table gives cross-reference parts and alternative options found for MB8S. The Form Fit Function (FFF) tab will give you the options that are more likely to serve as direct pin-to-pin alternates or drop-in parts. The Functional Equivalents tab will give you options that are likely to match the same function of MB8S, but it may not fit your design. Always verify details of parts you are evaluating, as these parts are offered as suggestions for what you are looking for and are not guaranteed.
| Part Number | Manufacturer | Composite Price | Description | Compare |
|---|---|---|---|---|
| MB8S-T | Micro Commercial Components | Check for Price | Rectifier Diode, | MB8S vs MB8S-T |
MB8S Frequently Asked Questions (FAQ)
-
The recommended PCB layout involves placing the MB8S near the edge of the board, with a solid ground plane underneath. Thermal management involves using a heat sink with a thermal conductivity of at least 1 W/m-K, and ensuring good airflow around the component.
-
To ensure reliable communication, use a dedicated serial communication line, implement proper signal termination, and ensure the microcontroller's serial communication protocol matches the MB8S's protocol (e.g., UART, SPI, or I2C).
-
The MB8S can operate within a temperature range of -40°C to 85°C, but optimal performance is achieved between 0°C and 70°C. Operating outside this range may affect accuracy and reliability.
-
Calibration involves adjusting the internal registers to compensate for manufacturing variations. Refer to the application note or contact Yangzhou Yangjie Electronics Co Ltd for specific calibration procedures and recommended values.
-
The typical response time for the MB8S to settle after a power-on reset is around 10-20 ms, but this may vary depending on the specific application and operating conditions.