Datasheets
LFCN-6000D+ by: Mini-Circuits

Ceramic LPF, 7 Section(s) Min, 7 Section(s) Max, 6800MHz, ROHS COMPLIANT, CERAMIC, CASE FV1206, 4 PIN

Part Details for LFCN-6000D+ by Mini-Circuits

Results Overview of LFCN-6000D+ by Mini-Circuits

Tip: Data for a part may vary between manufacturers. You can filter for manufacturers on the top of the page next to the part image and part number.

Applications Consumer Electronics Audio and Video Systems Renewable Energy

LFCN-6000D+ Information

LFCN-6000D+ by Mini-Circuits is a Ceramic Filter.
Ceramic Filters are under the broader part category of Filters.

A filter is an electronic circuit that selectively allows certain frequencies to pass while attenuating others. They are used to extract desired signals and remove noise. Read more about Filters on our Filters part category page.

Price & Stock for LFCN-6000D+

Part # Distributor Description Stock Price Buy
DISTI # 3157-LFCN-6000D+CT-ND
DigiKey LTCC LOW PASS FILTER, DC - 6000 Min Qty: 1 Lead time: 15 Weeks Container: Cut Tape (CT), Digi-Reel®, Tape & Reel (TR) 1005
In Stock
  • 1 $4.6000
  • 20 $4.1760
  • 50 $3.7200
  • 100 $3.2640
  • 200 $2.9760
  • 500 $2.8200
  • 1,000 $2.7000
$2.7000 / $4.6000 Buy Now
DISTI # 139-LFCN-6000D
Mouser Electronics Signal Conditioning LOW PASS FLTR / SURF MT / RoHS RoHS: Compliant 1379
  • 1 $4.3100
  • 10 $4.2800
  • 20 $4.1800
  • 50 $3.7200
  • 100 $3.2600
  • 200 $2.9800
  • 500 $2.8200
  • 1,000 $2.7000
  • 2,000 $2.6400
$2.6400 / $4.3100 Buy Now

Part Details for LFCN-6000D+

LFCN-6000D+ Part Data Attributes

LFCN-6000D+ Mini-Circuits
Buy Now Datasheet
Compare Parts:
LFCN-6000D+ Mini-Circuits Ceramic LPF, 7 Section(s) Min, 7 Section(s) Max, 6800MHz, ROHS COMPLIANT, CERAMIC, CASE FV1206, 4 PIN
Select a part to compare:
Pbfree Code Yes
Rohs Code Yes
Part Life Cycle Code Active
Ihs Manufacturer MINI-CIRCUITS
Package Description ROHS COMPLIANT, CERAMIC, CASE FV1206, 4 PIN
Reach Compliance Code compliant
ECCN Code EAR99
Samacsys Manufacturer Mini-Circuits
Additional Feature TAPE AND REEL
Attenuation Frequency (+/- delta f)-Max 1900000 kHz
Attenuation Frequency (+/- delta f)-Min 1700000 kHz
Attenuation@Freq-Max 30 dB
Attenuation@Freq-Min 20 dB
Average Input Power 9 W
Center or Cutoff Frequency (fo/fc) 6800 MHz
Filter Type CERAMIC LPF
Height 0.94 mm
Input/Output Impedance 50 OHM
Insertion Loss-Max 3 dB
JESD-609 Code e3
Length 3.2 mm
Mounting Type SURFACE MOUNT
Number of Sections-Max 7
Number of Sections-Min 7
Number of Terminals 4
Operating Temperature-Max 100 °C
Operating Temperature-Min -55 °C
Terminal Finish MATTE TIN OVER NICKEL
VSWR 1.3
Width 1.6 mm

LFCN-6000D+ Frequently Asked Questions (FAQ)

  • Mini-Circuits recommends a 4-layer PCB with a solid ground plane, and a via-stitched ground plane on the top and bottom layers. The device should be placed near the edge of the board, with the input and output ports facing away from each other. A low-impedance path to ground is essential for the device's internal biasing network.

  • The LFCN-6000D+ requires a single +5V supply and a bias current of 100mA. Ensure that the power supply is clean and well-regulated, and that the bias current is set to the recommended value using a suitable resistor network. Consult the datasheet for specific biasing recommendations.

  • The LFCN-6000D+ can handle input powers up to +20dBm without damage. However, operation above +15dBm may result in reduced performance and increased distortion. It is recommended to use an attenuator or limiter to ensure that the input power does not exceed the recommended maximum.

  • The LFCN-6000D+ is a broadband device, but its performance can be optimized for a specific frequency range by adjusting the input and output matching networks. Consult the datasheet for guidance on designing custom matching networks, and use simulation tools such as ADS or Genesys to optimize the design.

  • The typical noise figure of the LFCN-6000D+ is around 3.5dB. To minimize noise figure, ensure that the input and output ports are properly matched, and that the device is operated at the recommended bias current and voltage. Additionally, use a low-noise power supply and minimize electromagnetic interference in the surrounding environment.